Cast stone

We at Ventura cast stone are pleased to introduce this lightweight GFRC cast stone or lightweight precast concrete if you will, into our line of precast concrete and cast stone. Because lightweight cast stone is made from fiberglass strand mixed with real limestone which gives it that stone look, it is suitable for fireplace mantle treatments.

Lightweight precast concrete
 Lightweight precast concrete is usually called GFRC or glass fiber reinforced concrete, and is manufactured by Ventura cast stone and installed in the Los Angeles, Ventura and Santa Barbara Counties. Precast concrete usually weights 100 lbs per cubic foot.  Gfrc usually weights 10 lbs per lin foot.  Precast concrete is a lower end product and does not simulate limestone as does cast stone. Precast concrete resembles finished concrete and the surface looks like your garage floor. Cast stone resembles limestone or sandstone. Lightweight GFRC precast concrete is not a new product but has been used for years, but not in architectural uses.

Our Cast Stone range of products are into two product types:

Dry Cast

The "Dry Cast" method is a two part process, a face material to give you the similar finish to natural stone. Mechanically compacted to the rear of this is the backing mix to give the units strength in the terms of handling ability

Dry cast units are immediately demoulded after casting and are hand finished to a very high standard.

Wet Cast

Wet Cast as the name suggests produces structural products like heads and sills but is also used for slabs, beams and other similar products, that are for high exposure or structural situations where greater loads are required on the finished unit. The Wet Cast also has the added advantage of specialist finishes with the use of special sand aggregates, a massive spectrum of colors can be achieved.

Introduction to Cast Stone (wet cast and dry cast)

Cast Stone is known by a variety of other names including art stone, reconstructed stone, reconstituted stone, artificial stone and manufactured stone. This defines cast stone as any material manufactured with aggregate and cementicious binder and intended to resemble in appearance, and be used in a similar way to, natural stone. Cast stone is either homogenous through out or consists of a facing material and backing concrete.

The method of production is split into two categories.

Choice of manufacturing method

The majority of cast stone manufactures use the semi-dry method of production. And is the more commonly widely used method of manufacture. Early consultation with us is advisable to ascertain the correct method of production for your project.

Sizes: Components produced using the semidry method are limited in size with face dimensions of Ashlar units normally no greater than 1200x600mm. This is mainly because of the fact a semi dry mix is used, which require rapid and rigorous compaction with hand held pneumatic tampers. The semidry method of production is best suited to traditionally sized ashlars quoins, sills, copings, door and window surrounds, etc.

Structural requirements: Components requiring reinforcement which is more complex than a few straight bars or a layer of fabric reinforcement, must be produced using the wet cast method of production. This is because it is difficult to achieve thorough compaction of semidry mixes around congested reinforcement.

Appearance: Cast stone can replicate a variety of stone colors and finishes. The semidry method of production is used to simulate limestones and sandstones. Where a component has a particularly intricate pattern or profile including slender projections, precast concrete may have to be used in preference to the 'semidry' method. Good color matching between components can be achieved by both methods, although textural differences become apparent at close range.

Economics: Rapid production rates with frequent reuse of moulds are possible with cast stone produced using semidry mixes. Where as with the Wet Cast process a higher number of concrete molds is required to achieve the same casting program, but careful thought a planning stages of the contract can minimize the number of concrete molds. In Fact an additional 2-3 weeks extra lead-time for standard or semi standard products can sometimes be all that is needed to achieve the same casting program.

Comparison between the semidry and wet methods

The production of cast stone using semidry mixes differs from that of wet method in several ways.

Casting

Semi Dry ~ De-molding takes place immediately after compaction. This allows a rapid casting cycle with e.g. up to 100 or more basic components (sills, copings, etc.) a day from a single mould.

Wet Cast ~ Where as to manufacture the equivalent in wet cast it would not only take longer but you would require 1 mould per cast per day i.e. to produce 100 units a day you would need 100 moulds.

Semi Dry ~Compaction is carried out by pneumatic tampers rather than by vibration.

Wet Cast ~ Compaction is carried out by vibration.

Mixes

Semi Dry ~ *Separate facing and backing mixes are often used for components like ashlars, sills, heads and jambs, where the backing mix is concealed from view. Separate facing and backing mixes are used primarily to economize on the facing mix. BS1 217 requires a separate facing mix to be not less than 20 mm thick at any point, with semidry cement sand facing mixes and concrete backing mixes each mix is placed and compacted in immediate succession to ensure that they are effectively monolithic.

Wet Cast ~ Wet Cast units are manufactured from a through colored homogenous mix.

Semi Dry ~ Water repellent admixtures are invariably used in facing mixes to reduce permeability. Giving a water absorption of Grade B. All constituents are accurately weigh batched with the moisture content monitored regularly. Mix batches are necessarily small to prevent any premature drying of the mix. Thorough mixing and compaction are critical to ensure that the cast stone achieves the required density (typically between 1850-2100kg/m2), compressive strength and permeability.

Wet Cast ~ superplasticisers and accelerators are used to ensure good flow of the mix during vibration and compaction to achieve a smooth, compact and blow hole free finish (where ever possible finish smooth after dressing) also to give good early strength. Typical cube tests at 7-10 Days are that of the equivalent of that of a semi dry unit at 28 Days

Products are split into three categories.

Standard - Cast stone items that are manufactured in accordance with our Technical specification sheets. These items could be stock items or units, which are ready to cast at the first available production slot, with no moulds to produce. Products like standard head, sills or pier caps and copings. The cost of establishing the moulds is not same, thus for small production runs costs can be kept to the minimum. Also not forgetting lead times can be much shorter by not having to detail, obtain approval and then construct moulds.

Semi Standard - Cast stone items, which are similar to details within our Technical specification sheets. But say vary in length or require slight mould adaptation or modification.

Purpose Made - Cast Stone items which are manufactured in accordance with the contract documents. These units are made from new purpose made concrete molds. These would probably be specialized units, which are not contained in our brochure. We have our own in house design department, who will assist you in the process of your design advising you in Careful thought must be given in the planning process for purpose made products. Please consider the following.

Remember adequate time must be allowed for production of concrete molds.

Colors and Finishes

Natural stone colors are achieved either by reliance on the color of crushed rock and sands and aggregates or by the addition of pigments. White cement gray cement and a combination are often used. The use of pigments can give the cast stone greater scope in the selection of suitably graded aggregates, which permit good compaction and achieve a strong, dense mix. Iron oxides based pigments are normally used in small quantities (e.g. 0.2%-1% yellow iron oxide by weight of cement for yellow sandstone's and up to 5% red iron oxide for red sandstone). High proportions of pigment powder (above say 6 - 8% by weight of cement) are used sometimes to achieve unusual colors like blues and browns but generally these should be avoided.

A variety of traditional ashlar finishes can be replicated with cast stone, including plain, boasted, tooled, rockfaced, vermiculated. The other ashlar finishes are normally produced from latex:sand or concrete mold liners.

Here is where specialist aggregates can be used to achieve some wonderful and varied finishes and colors.

Structural Use

Dependant on the situation all cast stone both Wet and Dry Cast can be used. But there are limitations in the Dry Cast process as opposed to Wet Cast: -

Precast concrete
Precast concrete is usually used in lower end track homes where budget is a concern, cast stone is usually used in higher end homes where budget is not a major concern. The difference between cast stone and precast concrete is easily seen, and even the novice can appreciate the high quality limestone like finish on a cast stone product. Fireplace mantels or as some call them fireplace mantles look beautiful when constructed from cast stone. Cast stone fireplace mantels are used in any situation.  The fireplace mantels are both strong and fireproof. Fireplace mantels are a thing of beauty when made from cast stone or precast concrete. Fireplace mantels are also made from wood. Fireplace mantels or fireplace chimneys are the main feature in any room and a fireplace mantel made from cast stone or precast concrete is a sight to behold.
Cast stone by Ventura Cast Stone installed in California city's such as Los Angeles, Beverly Hills, Bel Air, Ventura or Santa Barbara has to be mechanically fastened to the wood frame of a building usually with stainless steel or galvanized attachments, this because of earthquake codes.  There are many historical buildings in California with cast stone as part of their facade.  Cast stone in Los Angeles, Beverly hills, Bel Air, Ventura and Santa Barbara was at it's most popular in the 1900's.  In Santa Barbara, cast stone was used extensively in the downtown district and also in a primitive form at the Santa Barbara mission in the form of adobe, a mixture of mud and straw or horsehair mixed with water and hand shaped into molds.  Cast stone in the City of Ventura was used mainly on churches in the downtown area.  Cast stone in Los Angeles was used in many important buildings including the famous Los Angeles City hall.  In Santa Barbara cast stone and Santa Barbara stone were used in conjunction in many historical buildings.  Santa Barbara stone also called Santa Barbara sandstone, is found mainly in Santa Barbara county, is removed from the ground in loose form, the Santa Barbara stone is then cut and shaped by a stonemason into useable blocks.  Cast stone in Beverly Hills was used in the Beverly Hills City hall and is now used on many residential buildings.  We also supply and install granite and CDI precast caststone and concrete design product,  CDI columns, Sierra stone caststone columns and balustrade, California precast products, CDI precast, CDI precast granite moldings and stairs. We also supply and  install CDI precast granite concrete window and door trim, CDI GFRC columns, Sierra stone products, concrete design, full weight precast and granite or limestone products,  California precast columns, CDI precast pool coping, CDI precast or limestone moldings and CDI fireplace mantles.
We also install the products exclusively manufactured by other company's including, Sierra concrete design, Sierra stone and Dura art stone, Stone legends, Moonlight molds, Fineline precast, Concrete design inc. Studio cast design, Concrete design inc, CDI, Architectural products, Haddonstone.

 These products include: cast stone, limestone, precast concrete, precast, cast, stone, limestone, sandstone, los angeles, ventura, santa barbara, los angeles precast, los angeles columns, los angeles cast stone, santa barbara precast, santa barbara cast stone, santa barbara stone, santa barbara columns, ventura cast stone, ventura precast, ventura columns, ventura stone. These products include: cast stone, limestone, precast concrete, precast, cast, stone, limestone, sandstone, los angeles, ventura, santa barbara, los angeles precast, los angeles columns, los angeles cast stone, santa barbara precast, santa barbara cast stone, santa barbara stone, santa barbara columns, ventura cast stone, ventura precast, ventura columns, ventura stone, concrete molds.

Home